MECHANICAL PROPERTIES OF LAUNDRY WASTEWATER CONCRETE INCORPORATING POLYETHYLENE 2 TEREPHTHALATE (PET) AS PARTIAL REPLACEMENT FOR SAND

Authors

  • A. Oke Department of Civil and Environmental Engineering, Federal University of Technology Akure, Nigeria
  • O. M. Ojo Department of Civil and Environmental Engineering, Federal University of Technology Akure, Nigeria
  • T. O. Olabanji Department of Civil and Environmental Engineering, Federal University of Technology Akure, Nigeria
  • O. K. Akinmusere Department of Civil Engineering, Elizade University, Ilara-Mokin, Nigeria
  • S. P. Akande Department of Civil and Environmental Engineering, Federal University of Technology Akure, Nigeria

DOI:

https://doi.org/10.4314/njt.v43i4.2

Keywords:

Concrete, Laundry wastewater, PET, SEM, Regression

Abstract

Today’s scarcity of fresh water and a rise in polyethylene terephthalate (PET) waste in the environment results from the increase in population. This study examines the impact of utilizing laundry wastewater and PET in concrete production. Laundry wastewater (LWW) and varying percentages of PET (0% to 30%) used as partial replacement for fine aggregate were used to produce 84 concrete cylinders and 84 concrete cubes. The results showed that a 30% PET replacement significantly reduced the workability of concrete by 50% compared to the control mix, and the compaction factor was reduced by 5%. The PET-modified concrete with 5%, 10% and 15 % achieved a target compressive strength of 13.5 N/mm² at 7 days but did not meet the target at 14 and 28 days, unlike the control mix. Prolonged curing time resulted in increased split tensile strength, except for the 5% PET replacement, which showed a decrease at 28 days. Scanning electron microscope (SEM) analysis revealed that the cement and 10% PET aggregates possessed the strongest bond, while the 15% to 30% PET replacement exhibited weak interfacial transition zone (ITZ). Certain properties of the LWW such as increased suspended solids and organic compounds present in detergents and bleach could have reduced the bond strength between cement and aggregates. Regression analysis indicated that the percentage of pulverized PET is a reliable predictor of slump and compressive strength, but less so for tensile strength.

References

[1] Uche, C. K. A., Abubakar, S. A., Nnamchi, S. N., and Ukagwu, K. J. “Polyethylene terephthalate aggregates in structural lightweight concrete: a meta-analysis and review”, Discover Materials, 3 (1), 2023, 24.

[2] Kolhapure, B. K., Chavan, A., Irshad, A., Amar, B., and Patel, H. “Eco friendly concrete by partial replacement of sand by shredded pieces of PET plastic bottles”, International Research Journal of Engineering Technology, 5 (5), 2018, 1259-1263.

[3] Nadimalla, A., Masjuki, S. A. B., Saad, A. B., Ismail, K. M., and Ali, M. B. “Polyethylene terephthalate (PET) bottles waste as fine aggregate in concrete”, International Journal of Innovative Technology and Exploring Engineering (IJITEE), 8(6S4), 2019; 1177 - 1180.

[4] Praveen, M., Shibi, V., Thomas, P., and Eldho. V. “Recycled plastic as coarse aggregate for structural concrete”, International Journal of Innovation, Research, Science, Engineering and Technology, 2 (3), 2013, 687-690.

[5] Hassani, M. S., Matos, J. C., Zhang, Y. X. and Teixeira, E. “Concrete production with domestic and industrial wastewaters – A literature review”, Structural Concrete, 24 (4), 2023; 5582 – 5599.

[6] Tang, S. W., Yao, Y., Anderade, C., and Li, Z. J. “Recent durability studies on concrete structure. Cement Concrete Resources”, 78: 2015, 143 – 154.

[7] Babafemi, A. J., Šavija, B., Paul, S. C., and Anggraini, V. “Engineering properties of concrete with waste recycled plastic: a review”, Sustain, 2018.

[8] Mishra, B. K., Kumar, P., Saraswat, C., Chakraborty, S., and Gautam, A. “Water security in a changing environment: concept, challenges and solutions”, Water, 13(4), 2021; 490.

[9] Maddikeari, M., Das, B. B., Tangadagi, R. B., Roy, S., Nagaraj, P. B., and Ramachandra, M. L. “A Comprehensive Review on the Use of Wastewater in the Manufacturing of Concrete: Fostering Sustainability through Recycling”, Recycling, 9(3): 2024, 45.

[10] Intergovernmental Panel on Climate Change (IPCC) “Summary for Policymakers. In Climate Change 2013—The Physical Science Basis: Working Group I Contribution to the Fifth Assessment Report of the Intergovernm-ental Panel on Climate Change”, Cambridge University Press: Cambridge, UK, 2014, 1-30.

[11] Bhardwaj, B., and Kumar, P. “Waste foundry sand in concrete: A review”, Construction and building materials, 156: 2017, 661-674.

[12] Black, J. “The use of recycled polyethylene terephthalate as a partial replacement for sand on the mechanical properties of structural concrete”, Plymouth Student Scientist, 13 (1), 2020; 143 - 172.

[13] Frigione, M. “Recycling of PET bottles as fine aggregate in concrete”, Waste Management, 30 (6): 2010, 1101-1106.

[14] Chong, B. W., and Shi, X. “Meta-analysis on PET plastic as concrete aggregate using response surface methodology and regression analysis”, Journal of Infrastructure Preserva-tion and Resilience, 4(1): 2023, 2.

[15] Chowdhury, S., Maniar, A. T., and Suganya, O. “Polyethylene terephthalate (PET) waste as building solution”, International Journal of Chemical, Environmental and Biological Science, 1: 2013, 308–312.

[16] Adnan, H. M., and Dawood, A. O. “Strength behavior of reinforced concrete beam using re-cycle of PET wastes as synthetic fibers”, Case Studies in Construction Materials, 13: 2020, e00367.

[17] Kaur, G. and Pavia, S. “Chemically treated plastic aggregates for eco-friendly cement mortars”, Journal of Material Cycles and Waste Management, 23: 2021,1531 - 1543.

[18] Marsiglio, L., Cheng, S., Falk, E., Fugh, A., Mulvaney, K., Slocum, B., Morris, D., Balasubramanian, G., and Mehta, K. “Comparing the properties of polyethylene terephthalate (PET) plastic bricks to conventional concrete masonry units”, In 2020 IEEE global humanitarian technology conference (GHTC), 2020, 1-6, IEEE.

[19] Haile, B. F., Jin, D. W., Yang, B., Park, S., and Lee, H. K. “Multi-level homogenization for the prediction of the mechanical properties of ultra-high-performance concrete”, Construction and Building Materials, 229: 2019, 116797.

[20] Bamigboye, G. O., Tarverdi, K., Umoren, A., Bassey, D. E., Okorie, U., and Adediran, J. “Evaluation of eco-friendly concrete having waste PET as fine aggregates”, Clean Materials, 2: 2021, 100026.

[21] Dawood, A. O., AL-Khazraji, H., and Falih, R. S. “Physical and mechanical properties of concrete containing PET wastes as a partial replacement for fine aggregates”, Case Studies in Construction Materials, 14, 2021.

[22] Kangavar, M. E., Lokuge, W., Manalo, A., Karunasena, W., and Frigione, M. “Investigation on the properties of concrete with recycled polyethylene terephthalate (PET) granules as fine aggregate replacement”, Case Studies in Construction Materials, 16: 2022, e00934.

[23] Faraj, R. H., Sherwani, A. H., and Daraei A. “Mechanical, fracture and durability properties of self-compacting high strength concrete containing recycled polypropylene plastic particles”, Journal of Building Engineering, 25: 2019, 100808.

[24] Akçaözoǧlu, S., Atiş, C. D., and Akçaözoǧlu K. “An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete”, Waste Management, 30 (2): 2010, 285-290.

[25] Askar, M. K., Askar, L. K., Al-Kamaki, Y. S., S. and Ferhadi, R. “Effects of chopped CFRP fiber on mechanical properties of concrete”, Heliyon, 9: 2023, e13832.

[26] Colangelo, F., Cioffi, R., Liguori, B., and Iucolano, F. “Recycled polyolefins waste as aggregates for lightweight concrete”, Composite Part B Engineering, 106: 2016, 234 - 241.

[27] ASTM C150-04. “Standard Specification for Portland Cement”, 4.1: 2004, 1-8.

[28] An, M., Huang, H., Wang, Y., and Zhao, G. “Effect of thermal cycling on the properties of high-performance concrete: Microstructure and mechanism”, Construction and Building Materails, 243: 2020, 118310.

[29] Boucedra, A., Bederina, M., and Ghernouti, Y. “Study of the acoustical and thermo-mechanical properties of dune and river sand concretes containing recycled plastic aggregates”, 2020.

[30] Dahegaokar, A. D., and Dudhe, A. D. “Physical and Chemical Properties of Cement – A Study”, International Journal of Creative Research Thoughts, 11 (11): 2023; a440 – a445.

[31] Rainwater, F. H. and Thatcher, L. L. “Methods for collection and analysis of water samples (No. 1454-1458)”, US Government Printing Office, 1960.

[32] ASTM C143/C143M-15a, “Standard Test Method for Slump of Hydraulic-Cement Concrete”, West Conshohocken, PA. 2015.

[33] ASTM C39-12, “Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens”, Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA, 2012.

[34] ASTM C496/C496M-17, (2017). Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens.

[35] Akinbile, C. O., Epebinu, E. M., Olanrewaju, O. O., and Abolude, A. T. “Comparative Analysis of Bamboo-based (Bambusa vulgaris) Activated Carbon produced through Trioxonitrate (V) Acid and Potassium Hydroxide”, Nigerian Journal of Technological Development, 20 (2), 2023.

[36] Umasabor, R. I. and Daniel, S. C. “The effect of using polyethylene terephthalate as an additive on the flexural and compressive strength of concrete”, Heliyon, 6 (8), 2020.

[37] Shubbar, S. D. A., and Al-Shadeedi A. S. “Utilization of waste plastic bottles as fine aggregate in concrete”, Kufa Journal of Engineering, 8(2): 2017, 132 - 46.

[38] Al-Hadithi, A. I., and Al-Ani M. F. “Effects of adding waste plastics on some properties of high-performance concrete”, In: 11th international conference on developments in eSystems engineering, (I): 2018, 273–279.

[39] Almeshal, I., Tayeh, B. A., Alyousef, R., Alabduljabbar, H., and Mohamed A. M. “Eco-friendly concrete containing recycled plastic as partial replacement for sand”, Journal of Material Research and Technology, 9 (3): 2020, 4631-4643.

[40] Amalu, R., Azeef, A., Muhammad, H., Rejith, K., and Vijitha, V. “Use of Waste Plastic as Fine Aggregate Substitute in Concrete”, International Journal of Science and Engineering Research, 7, 2016.

[41] Azhdarpour, A. M., Nikoudel, M. R., and Taheri, M. “The effect of using polyethylene terephthalate particles on physical and strength-related properties of concrete; A laboratory evaluation”, Construction and Building Materials, 109: 2016, 55-62.

[42] Rahmani, E., Dehestani, M., Beygi, M. H. A., Allahyari, H., and Nikbin, I. M. “On the mechanical properties of concrete containing waste PET particles”, Construction and Building Materials, 47: 2013, 1302-1308.

[43] Ferreira, L., de Brito, J., and Saikia, N. “Influence of curing conditions on the mechanical performance of concrete containing recycled plastic aggregate”, Construction and Building Materials, 36: 2012, 196 - 204.

[44] Akinyele, J., and Ajede, A. “The use of granulated plastic waste in structural concrete”, Afr. Journal of Science and Technology Innovation and Development, 10: 2018, 169 – 175.

[45] Saxena, R., Siddique, S., Gupta, T., Sharma, R. K. and Chaudhary, S. “Impact resistance and energy absorption capacity of concrete containing plastic waste”, Construction and Building Materials, 2018, 176: 415-421.

[46] Mastan, V. N. and Asadi, S. S. “P.E.T. bottle waste as a supplement to concrete fine aggregate”, International Journal of Civil Engineering and Technology, 2017, 8(1):558 - 568.

[47] Akçaözoǧlu, S., Akçaözoǧlu, K., and Duran, A. C. “Thermal conductivity, compressive strength and ultrasonic wave velocity of cementitious composite containing waste PET lightweight aggregate (WPLA)”, Composite Part B, 2013, 45: 721 - 726.

Downloads

Published

2025-01-08

Issue

Section

Building, Civil & Geotechnical Engineering

How to Cite

MECHANICAL PROPERTIES OF LAUNDRY WASTEWATER CONCRETE INCORPORATING POLYETHYLENE 2 TEREPHTHALATE (PET) AS PARTIAL REPLACEMENT FOR SAND. (2025). Nigerian Journal of Technology, 43(4), 618 – 627. https://doi.org/10.4314/njt.v43i4.2