DESIGN AND FABRICATION OF A WASTE PLASTIC FILAMENT EXTRUDER
DOI:
https://doi.org/10.4314/njt.v43i3.24Keywords:
Plastic recycling, high-density polyethylene, extrusion, filamentAbstract
Plastic pollution causes serious environmental issues and endangers the health of humans and animals in both land and aquatic environments. Despite the fact that Nigeria produces hundreds of tons of plastic waste every day, a greater proportion still finds its way back into the ecosystem because only a small portion of it is recycled. Nigeria's growing production of single-use plastics and careless disposal of plastic waste into the land and ocean are the main causes of the country's growing plastic pollution problems. For this reason, recycling and reusing plastics is necessary to lessen the harmful effects that plastic utilization has on both human and the environment.. Plastics can be recycled into filaments used in 3D printing also known as additive manufacturing. In this study, a plastic filament extrusion machine for waste plastic was designed and developed with the aim of recycling high-density polyethene, thereby lessening the negative environmental effects that come with disposing of it.. The basic components of the extruder comprised of a hopper, screw, barrel, die, and motor system. Temperature, oxygen, and shear stress all cause the plastics to deteriorate during the extrusion of plastics for filament.. Thus, this study examined the impact of different extrusion temperatures on the filament quality made from high-density polyethylene polyethene (HDPE). The plastic pellets melt and flow into the die as a result of friction between them and the barrel surface and the heat generated by the heating bands. Plastic filament was extruded with a combination of optimal pellet compression, temperatures between 150 and 230 degrees Celsius, and a gradual increase in the pressure of the molten pellets inside the barrel.. Melted plastic adhered itself to the barrel at low temperatures but turned to char at high temperature. Consequently, in order to produce quality 3D filament using HDPE, it is imperative to maintain acceptable temperature conditions. Based on the results, the extruder produced excellent filament suitable for 3D printing at 200 oC. The results of this study emphasize the significance of temperature regulation during the extrusion process in order to guarantee the intended filament quality.
References
[1] Plastic atlas. Facts and figures about the world of synthetic polymers - Nigeria Edition. (2020). Heinrich Böll Stiftung. www.ng.boell.org/plast icatlasnigeria.
[2] Babayemi, J. O., Nnorom, I. C., Osibanjo, O., and Weber, R. “Ensuring sustainability in plastics use in Africa: Consumption, waste generation, and projections”, Environmental Sciences Europe, 31(1), 2019; pp 1-20. https://doi.org/10.1186/s12302-019-0254-5
[3] Soares, J., Miguel, I., Venâncio, C., Lopes, I., and Oliveira, M. “Public views on plastic pollution: Knowledge, perceived impacts, and pro-environmental behaviours”, Journal of Hazardous Materials, 412, 125227. 2021. https://doi.org/10.1016/j.jhazmat.2021.125227
[4] Evode, N., Qamar, S. A., Bilal, M., Barceló, D., and Iqbal, H. M. “Plastic waste and its management strategies for environmental sustainability”, Case Studies in Chemical and Environmental Engineering, 4, 100142. 2021. https://doi.org/10.1016/j.cscee.2021.100142
[5] Aboulkas A, El harfi K, and El Bouadili, A. Thermal degradation behaviors of polyethylene and polypropylene. Part I: Pyrolysis kinetics and mechanisms. Energy Convers Manag 51, 2010; pp 1363–1369. https://doi.org/10.1016/ j.enconman.2009.12.017
[6] Cruz Sanchez, F. A., Boudaoud, H., Camargo, M., and Pearce, J. M. “Plastic recycling in additive manufacturing: A systematic literature review and opportunities for the circular economy”. Journal of Cleaner Production, 264, 121602. 2020. https://doi.org/10.1016/j.jclepro .2020.121602
[7] Rett, J. P., Traore, Y. L., and Ho, E. A. “Sustainable Materials for Fused Deposition Modeling 3D Printing Applications”, Advanced Engineering Materials, 23(7), 2001472. 2021. https://doi.org/10.1002/adem.202001472
[8] Alzahrani, M. “Modification of recycled poly (ethylene terephthalate) for FDM 3D-printing applications”, MS thesis. University of Waterloo, 2017.
[9] Oussai, A., Bártfai, Z. and Kátai, L. “Development of 3D printing raw materials from plastic waste. A case study on recycled polyethylene terephthalate”, Applied Science, 11, 7338. 2021. https://doi.org/10.3390/app11 167338.
[10] Bremer, M., Janoschek, L., Kaschta, Schneider, N. and Wahl, M. “Influence of plastic recycling: a feasibility study for additive manufacturing using glycol modified polyethylene terephthalate (PETG)”, SN Appl. Sci. 4, 2022, 156. https://doi.org/10.1007/s424 52-022-05039-3
[11] Mikula, K., Skrzypczak, D., Izydorczyk, G., Warchoł, J., Moustakas, K., Chojnacka, K., and Witek-Krowiak, A. “3D printing filament as a second life of waste plastics: a review”, Environmental Science and Pollution Research, 28, 2021, pp 12321 – 12333. https://doi.org/10.1007/s11356-020-10657-8
[12] Hassan, M., Mohanty, A. K., and Misra, M. “3D printing in upcycling plastic and biomass waste to sustainable polymer blends and composites: A review”, Materials and Design, 237, 112558. 2023. https://doi.org/10.1016/j. mat des.2023.112558.
[13] Velghe, I., Buffel, B., Vandeginste, V., Thielemans, W., and Desplentere, F. “Review on the Degradation of Poly(lactic acid) during Melt Processing”, Polymers, 15(9). 2023. https://doi.org/10.3390/polym15092047
[14] Raza S. M. “Experimental investigation on filament extrusion using recycled materials”, M.Sc Thesis, Halmstad University. 2020.
[15] Herianto, Atsani, S. I., and Mastrisiswadi, H., “Recycled Polypropylene Filament for 3D Printer: Extrusion Process Parameter Optimization”, Materials Science and Engineering Conference Series (i), vol. 722, (1), 2020. p. 012022. doi:10.1088/1757-899X/722/1/012022.
[16] Rauwendaal, C. “Polymer Extrusion”, Cincinnati. USA: Hanser Publications. 2014.
[17] FTIR. “Spectroscopy of Polymers and Additives with IROS”, Dynisco/Kayeness Polymer Test Systems. 1996.
[18] Hamod, H. “Suitability of recycled HDPE for 3D printing filament”, Degree Thesis, Arcada University of Applied Science. 2014.
[19] Stevens, M. J., and Covas, J. A. “Extruder principles and operation”, Springer Science and Business Media. 2012.
[20] Kruder, G. A., and Nunn, R. E. “Extruder efficiency: how you measure it-how you get it”, Electr. Conserv. Q.;(India), 2(3), 1982, pp 7 -10
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Nigerian Journal of Technology
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
The contents of the articles are the sole opinion of the author(s) and not of NIJOTECH.
NIJOTECH allows open access for distribution of the published articles in any media so long as whole (not part) of articles are distributed.
A copyright and statement of originality documents will need to be filled out clearly and signed prior to publication of an accepted article. The Copyright form can be downloaded from http://nijotech.com/downloads/COPYRIGHT%20FORM.pdf while the Statement of Originality is in http://nijotech.com/downloads/Statement%20of%20Originality.pdf
For articles that were developed from funded research, a clear acknowledgement of such support should be mentioned in the article with relevant references. Authors are expected to provide complete information on the sponsorship and intellectual property rights of the article together with all exceptions.
It is forbidden to publish the same research report in more than one journal.
How to Cite
